Milwaukee-tool 2762-20 User Manual download pdf (Page 3)

Attaching and Removing Accessories

1/2" Impact Wrench with Pin

(Cat. No. 2762-20)

1. Use only the appropriate size Square Drive

Sockets.

2. To attach a socket, align the hole in the acces-

sory with the detent pin on the anvil. Hold the

detent pin in while pushing the socket onto the

anvil. The detent pin will snap into place in the

hole to secure the socket.

3. To remove the socket, insert a nail or other thin

object into the hole in the accessory and press

in the detent pin. Pull the accessory off the anvil.

1/2" and 3/4" Impact Wrench with Ring

(Cat. No. 2763-20, 2764-20)

1. Use only the appropriate size Square Drive

Sockets.

2. To attach a socket, align the accessory with the

anvil and push it ﬁ rmly over the retaining ring.

3. To remove the accessory, pull the accessory

off the anvil.

7/16" Hex Impact Wrench (Cat. No. 2765-20)

This impact driver is intended for

use with drill and driver bits.

1. To attach an accessory, press

the shank into the hex drive

chuck.

2. To remove the accessory, pull

out the ring and remove the ac-

cessory. Release the ring.

ASSEMBLY

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and battery.

Inserting/Removing the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body of

the tool. Make sure it latches securely into place.

WARNING Use only sockets and other

accessories speciﬁ cally designed for use on

impact wrenches and drivers. Other sockets

and accessories might shatter or break caus-

ing injury.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

Starting, Stopping and Controlling Speed

These tools may be operated at any speed from

0 to full speed.

1. To start the tool, pull the trigger.

NOTE: An LED is turned on when the trigger is

pulled.

2. To vary the driving speed, increase or decrease

pressure on the trigger. The further the trigger is

pulled, the greater the speed.

3. To stop the tool, release the trigger.

Impacting Techniques

The longer a bolt, screw, or nut is impacted, the

tighter it will become. To help prevent damaging the

fasteners or workpieces, avoid excessive impact-

ing. Be particularly careful when impacting smaller

fasteners because they require less impacting to

reach optimum torque.

Practice with various fasteners, noting the length

of time required to reach the desired torque. Check

the tightness with a hand-torque wrench. If the

fasteners are too tight, reduce the impacting time.

If they are not tight enough, increase the impact-

ing time.

Oil, dirt, rust or other matter on the threads or

under the head of the fastener affects the degree

of tightness.

The torque required to loosen a fastener averages

75% to 80% of the tightening torque, depending on

the condition of the contacting surfaces.

On light gasket jobs, run each fastener down to a

relatively light torque and use a hand torque wrench

for ﬁ nal tightening.

Using the Drive Control

The drive control button is used to adjust the torque,

rotation speed (RPM), and impact speed (IPM) for

the application (see Speciﬁ cations chart for RPM

and IPM).

To select the drive control mode:

1. Pull and release the trigger to turn on the tool.

The current mode indicator is lit.

2. Press the drive control button to cycle through

the 2 modes. When the desired mode indicator

is lit, begin work.

Push for

Forward

Push for

Reverse

PUSH TO CENTER TO LOCK

OPERATION

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

Mode

Indicator

Drive Control Button

Using the Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the ON/OFF switch is not pressed. Always allow

the motor to come to a complete stop before using

the control switch.

1. For forward (clockwise) rotation, push the

control switch in the direction shown. Check the

direction of rotation before use.

2. For reverse (counterclockwise) rotation, push

the control switch in the direction shown. Check

the direction of rotation before use.

3. To lock the trigger, push the control switch to the

center position. The trigger will not work when

the control switch is in the locked position.

Always remove the battery pack before perform-

ing maintenance, changing accessories, storing

the tool and any time the tool is not in use.

Mode

Indicator

For a complete listing of accessories refer to your

MILWAUKEE Electric Tool catalog or go online

to www.milwaukeetool.com. To obtain a catalog,

contact your local distributor or service center.

WARNING Always remove battery pack

before changing or removing accessories.

Only use accessories speciﬁ cally recommend-

ed for this tool. Others may be hazardous.

ACCESSORIES

Maintaining Tool

Keep your tool, battery pack and charger in good

repair by adopting a regular maintenance program.

After six months to one year, depending on use,

return the tool, battery pack and charger to A

MILWAUKEE service facility for:

• Lubrication

• Mechanical inspection and cleaning (gears, spin-

dles, bearings, housing, etc.)

• Electrical inspection (battery pack, charger,

motor)

• Testing to assure proper mechanical and electrical

operation

If the tool does not start or operate at full power

with a fully charged battery pack, clean the contacts

on the battery pack. If the tool still does not work

properly, return the tool, charger and battery pack,

to a MILWAUKEE service facility for repairs.

Cleaning

Clean dust and debris from charger and tool vents.

Keep tool handles clean, dry and free of oil or

grease. Use only mild soap and a damp cloth to

clean the tool, battery pack and charger since certain

cleaning agents and solvents are harmful to plastics

and other insulated parts. Some of these include

gasoline, turpentine, lacquer thinner, paint thinner,

chlorinated cleaning solvents, ammonia and house-

hold detergents containing ammonia. Never use

ﬂ ammable or combustible solvents around tools.

Repairs

For repairs, return the tool, battery pack and

charger to the nearest service center.

WARNING To reduce the risk of per-

sonal injury and damage, never immerse your

tool, battery pack or charger in liquid or allow

a liquid to ﬂ ow inside them.

WARNING To reduce the risk of injury,

always unplug the charger and remove the

battery pack from the charger or tool before

performing any maintenance. Never disas-

semble the tool, battery pack or charger.

Contact a MILWAUKEE service facility for

ALL repairs.

MAINTENANCE

1 2 3 4 5 6 7 8 9 10 11

Comments to this Manuals

No comments

Milwaukee-tool 2762-20 User Manual Page 3

Comments to this Manuals

Related products and manuals for Power tools Milwaukee-tool 2762-20