Milwaukee-tool 2352-20 Safety 2 User Manual download pdf

M18™ FLOOD LIGHT

ÉCLAIRAGE PAR PROJECTION M18™

LÁMPARA DE TRABAJO M18™

IMPORTANT SAFETY INSTRUCTIONS

Before using the ﬂ ood light, read this operator's manual, your battery pack and charger operator's manual, and

all labels on the battery pack, charger and ﬂ ood light.

• Read and understand all the instructions before using the appliance.

• To reduce the risk of injury, close supervision is necessary when an appliance is used near children.

• Store idle ﬂ ood light out of reach of children. Warm ﬂ ood lights can become hazardous in the hands of

children.

• Do not use outdoors.

• For a rechargeable appliance - Use only the charger supplied by the manufacturer to recharge.

• Know your ﬂ ood light. Read this manual carefully to learn your ﬂ ood light's applications and limitations as

well as potential hazards associated with this type of tool.

• Batteries must be recharged only with the charger speciﬁ ed by the manufacturer. A charger that may be

suitable for one type of battery may create a risk of ﬁ re when used with another battery.

• Use ﬂ ood light only with speciﬁ cally designated battery pack. Use of any other batteries may create a risk

of ﬁ re.

• When battery pack is not in use, keep it away from metal objects like: paper clips, coins, keys, nails,

screws, or other small metal objects that can make a connection from one terminal to another. Shorting

the battery terminals together may cause sparks, burns, or a ﬁ re.

• Maintain labels and nameplates. These carry important information. If unreadable or missing, contact a

MILWAUKEE service facility for a free replacement.

SAVE THESE

INSTRUCTIONS

WARNING READ AND UNDERSTAND ALL INSTRUCTIONS. When using

electric appliances, basic precautions should always be followed, including the following:

Inserting/Removing Battery Pack

Insert the battery pack by sliding battery pack into the body of the tool. Insert the battery pack until the battery

latches lock.

To remove the battery pack, press in both battery latches and slide the battery pack off of the tool.

WARNING To reduce the risk of injury, do not look directly into the light when the

ﬂ ood light is on.

WARNING Recharge only with the charger speciﬁ ed for the battery. For speciﬁ c charg-

ing instructions, read the operator’s manual supplied with your charger and battery.

Operation

To turn on the ﬂ ood light, press the ON/OFF button

. The light will default to high mode. Press the but-

ton for the low setting. Press the

button for the high setting. To turn off the ﬂ ood light, press the ON/OFF

button

again .

If the ﬂ ood light does not turn on with a fully charged battery pack, remove the battery pack for one minute and

then reinsert to reset the ﬂ oodlight.

Hang/Mount

There are many ways to orient the ﬂ ood light to best suit your job.

• Hang or hold the ﬂ ood light from the top handle.

• Set the ﬂ ood light on one of eight sides.

• Use the key-hole to hang the ﬂ ood light on a screw.

• The notch in the side bar can balance the ﬂ oodlight on a wire.

• Mount on a user-built stand using a 3/4" bar.

• String up on a wire run through the pass-through holes.

Cleaning

Keep tool handles clean, dry and free of oil or grease. Use only mild soap and a damp cloth to clean the tool, bat-

tery pack and charger since certain cleaning agents and solvents are harmful to plastics and other insulated parts.

Some of these include gasoline, turpentine, lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia

and household detergents containing ammonia. Never use ﬂ ammable or combustible solvents around tools.

Maintain Flood light

Keep your ﬂ ood light, battery pack and charger in good repair by adopting a regular maintenance program. If the

ﬂ ood light does not work properly, return the ﬂ ood light to a MILWAUKEE service facility for repairs.

MAINTENANCE

WARNING To reduce the risk of injury, always unplug the charger and remove the

battery pack from the charger or tool before performing any maintenance. Never disassemble the tool,

battery pack or charger. Contact a MILWAUKEE service facility for ALL repairs.

WARNING To reduce the risk of personal injury and damage, never immerse your

tool, battery pack or charger in liquid or allow a liquid to ﬂ ow inside them.

ACCESSORIES

For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go online to

www.milwaukeetool.com. To obtain a catalog, contact your local distributor or a service center.

WARNING Always remove battery pack before changing or removing accessories.

Only use accessories speciﬁ cally recommended for this tool. Others may be hazardous.

TO REDUCE THE RISK OF INJURY, USER MUST READ AND

UNDERSTAND OPERATOR'S MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT

LIRE ET BIEN COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y

ENTENDER EL MANUAL DEL OPERADOR.

AVERTISSEMENTVOUS DEVEZ LIRE ET COMPRENDRE TOUTES LES

INSTRUCTIONS

Lors de l’utilisation d’outils électriques, toujours suivre les consignes de base,

notamment :

RÈGLES IMPORTANTES DE SÉCURITÉ

Avant d’utiliser l'éclairage par projection, lire le présent manuel d’utilisation et celui du bloc-piles et du chargeur,

ainsi que toutes les étiquettes se trouvant sur le bloc-piles, le chargeur et l'éclairage par projection.

• Lire et bien comprendre toutes les instructions avant d’utiliser l’appareil.

• Pour réduire les risques de blessures, porter une attention particulière lorsque le produit est utilisé en

présence d’enfants.

• Entreposer l'éclairage par projection non utilisé hors de la portée des enfants. Les éclairages par projec-

tion chauds peuvent être dangereux dans les mains des enfants.

• Ne pas utiliser cet outil à l’extérieur.

• S’il s’agit d’un outil rechargeable, utiliser exclusivement le chargeur fourni par le fabricant aﬁ n de le recharger.

• Savoir votre éclairage par projection. Lire attentivement ce manuel pour apprendre les applications et les

limites de votre éclairage par projection, ainsi que les risques spéciﬁ ques relatifs à son utilisation.

• Doit être rechargée seulement avec le chargeur spéciﬁ é pour la pile. Un chargeur adapté à un certain type

de pile peut créer un risque d’incendie s’il est utilisé avec d’autres piles.

• N’utiliser l'éclairage par projection qu’avec le bloc-piles recommandé. L'usage de toutes autres piles peut

créer un risque d'incendie.

• Lorsque le bloc-batterie n'est pas en service, tenez-le à l'écart d'autres objets métalliques (trombones,

pièces de monnaie, clés, clous, vis, etc.) susceptibles d'établir un contact électrique entre les deux

bornes. La mise en court-circuit des bornes de la batterie peut produire des étincelles et constitue un risque

de brûlures ou d'incendie.

• Entretenez les étiquettes et marques du fabricant. Les indications qu'elles contiennent sont précieuses. Si

elles deviennent illisibles ou se détachent, faites-les remplacer gratuitement à un centre de service MILWAUKEE

accrédité.

CONSERVEZ CES

INSTRUCTIONS

MONTAGE DE L'OUTIL

AVERTISSEMENT Ne recharger la batterie qu’avec le chargeur spéciﬁ é.

Pour les instructions de charge spéciﬁ ques, lire le manuel d’utilisation fourni avec le chargeur et les

batteries.

Insertion du bloc de piles dans l’outil

Insérez le bloc de piles à partir de l'avant en le faisant glisser dans le corps de l'outil. Insérez le bloc de

piles jusqu'à ce que son loquet se verrouille.

Pour retirer le bloc de piles, enfoncez les deux loquets de la pile et faites glisser le bloc hors de l'outil.

AVERTISSEMENT Pour réduire les risques de blessures, ne pas regarder

directement dans la source lumineuse lorsque l'éclairage est allumé.

Utilisation

Pour allumer l'éclairage par projection, appuyer sur le bouton « On/Off » (Marche/Arrêt). La lumière est en

mode élevé par défaut. Appuyer sur le bouton pour le réglage bas. Appuyer sur le bouton pour le réglage

élevé. Pour l’éteindre, appuyer de nouveau sur le bouton

« On/Off » (Marche/Arrêt).

Si l'éclairage par projection ne s'allume pas en utilisant un bloc-pile complètement chargé, retirer le bloc-pile et

attendre 1 minute avant de le réinsérer pour réinitialiser l'éclairage par projection.

Suspendre / Monter

Vous pouvez orienter votre éclairage par projection de plusieurs façons pour satisfaire le mieux à votre travail.

• Suspendre ou soutenir l'éclairage par projection de la poignée supérieure.

• Mettre l'éclairage par projection sur l'un de ses huit côtés.

• Utiliser le trou de serrure pour suspendre l'éclairage sur une vis.

• L'encoche dans la barre latérale peut mettre l'éclairage en équilibre sur un ﬁ l.

• Monter sur un support installé par l'utilisateur à l'aide de la barre de 19 mm (3/4")

• Enchaîner sur un ﬁ l traversant les passe-ﬁ ls.

Entretien de l'éclairage par projection

Garder l'éclairage par projection, le bloc-piles et le chargeur en bon état en le soumettant à un programme

d’entretien régulier. Si l’éclairage par projection ne fonctionne toujours pas correctement, le conﬁ er à un centre

de service MILWAUKEE aﬁ n de le faire réparer.

MAINTENANCE

AVERTISSEMENT Pour minimiser les risques de blessures corporelles,

débranchez le chargeur et retirez la batterie du chargeur ou une lampe torche avant d’y effectuer

des travaux d’entretien. Ne démontez jamais une lampe torche, la batterie ou le chargeur. Pour toute

réparation, consultez un centre de service MILWAUKEE accrédité.

PICTOGRAPHIE

Volts

Tension CD seul.

Underwriters Laboratories, Inc.,

États-Unis et Canada

SYMBOLOGY

Volts

Direct Current

Underwriters Laboratories, Inc.

United States and Canada

TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.

This warranty card covers any defect in material and workmanship on this Power Tool.

To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you purchased the

product, to the Authorized Service Center (ASC). Or, if this card has not been sealed/stamped, present the original proof of

purchase to the ASC.

Call toll-free 1 800 832 1949 to ﬁ nd the nearest ASC, for service, parts, accessories or components.

Procedure to make this warranty valid

Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you purchased the

product, and there any faulty piece or component will be replaced without cost for you. We will cover all freight costs relative

with this warranty process.

Exceptions

This warranty is not valid in the following situations:

a) When the product is used in a different manners from the end-user guide or instruction manual.

b) When the conditions of use are not normal.

c) When the product was modiﬁ ed or repaired by people not authorized by TECHTRONIC INDUSTRIES.

Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.

SERVICE AND ATTENTION CENTER

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

Ph. 52 55 4160-3547

IMPORTED AND COMMERCIALIZED BY:

TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.

Av Presidente Mazarik 29 Piso 7, 11570 Chapultepec Morales

Miguel Hidalgo, Distrito Federal, Mexico

LIMITED WARRANTY - USA AND CANADA

LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN

Model:

Date of Purchase:

Distributor or Store Stamp:

Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct CORDLESS

BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is warranted to the original

purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE will

repair or replace any part on an electric power tool which, after examination, is determined by MILWAUKEE to be defec-

tive in material or workmanship for a period of ﬁ ve (5) years* after the date of purchase unless otherwise noted. Return

of the power tool to a MILWAUKEE factory Service Center location or MILWAUKEE Authorized Service Station, freight

prepaid and insured, is required. A copy of the proof of purchase should be included with the return product. This warranty

does not apply to damage that MILWAUKEE determines to be from repairs made or attempted by anyone other than

MILWAUKEE authorized personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.

*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and Trade Titan™ Industrial Work

Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED Upgrade Bulb is

a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb fails the Work Light or

Upgrade Bulb will be replaced free of charge.

*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline Driven

Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets, Reconditioned

product and Test & Measurement products. There are separate and distinct warranties available for these products.

Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product. The

manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at

the time warranty service is requested.

ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION

OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE TO THIS

CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE LIABLE FOR

ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES,

EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF,

OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF PROFITS. SOME

STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO

THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU

OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAU-

KEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS

NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE

EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN

IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU

SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

This warranty applies to product sold in the U.S.A. and Canada only.

Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.milwaukeetool.

com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty and non-warranty

service on a Milwaukee electric power tool.

1 2

Summary of Contents

Page 1 - LÁMPARA DE TRABAJO M18™

M18™ FLOOD LIGHTÉCLAIRAGE PAR PROJECTION M18™LÁMPARA DE TRABAJO M18™IMPORTANT SAFETY INSTRUCTIONSBefore using the ﬂ ood light, read this operator&apos

Page 2 - SIMBOLOGÍA

MILWAUKEE ELECTRIC TOOL CORPORATION58-14-2361d2 07/13 13135 West Lisbon Road • Brookﬁ eld, Wisconsin, U.S.A. 53005 Printed in ChinaAntes de utiliza

Comments to this Manuals

No comments

Milwaukee-tool 2352-20 Safety 2 User Manual

Browse online or download User Manual for Lighting Milwaukee-tool 2352-20 Safety 2. Milwaukee Tool 2352-20 Safety 2 User Manual

Summary of Contents

Comments to this Manuals